If you want to tune your automobile’s performance and get it track-ready, ensure that you make the most out of your Hankook Tyres Ashford
Wheels: Select the widest wheels permitted in your vehicle’s category. They must be compatible with the vehicle and suggested by the tyre maker for your tyre dimensions.
Alignment-Springs and Sway Bars: During turns, hold the tyres at a right angle and try achieving neutral steering. In rear-wheel-drive vehicles use power oversteer to do so.
Shock Absorbers: Will assist in fine-tuning transitional performance.
Inflation Pressures: Choose the minimum allowable tyre air level. Although greater inflation levels improve response, they forfeit grip. If inconsistent wearing occurs at low inflation levels, raise them.
Here’s our advice to get those tyres ready:
-
Do not leave bare tyres on a vehicle trailer’s tyre rack between events. Or even out the front of your store. Place these in a dry storage area that doesn’t heat up. You want to keep tyres far from electric motors.
-
Clear any debris before examining the tyres for deterioration and wear soon after each track ride. Allow the tyres to cool once they’re off the floor.
-
The warmth of a tyre’s tread as measured using a pyrometer won’t be uniform over the surface. Unless you’ve just finished a good skid pad tweaking.
-
Tyre inflation level rises by a psi per each ten degrees rise in atmospheric temperature.
-
Protect tyres from harsh sunlight between track runs to the best of your ability. The warmth from the sun would cause the tyre’s inflation level to rise.
-
Experts recommend warm tyre inflation levels for autocross and hot inflation levels for roadside events.
-
Monsoon tyres ought to have higher initial inflation levels than dry tyres for races or track-related events.
-
Tyres are a component of the suspension. Opting for low-profile tyres is the same as using shorter, stiffer suspensions.
Is Shaving a good idea for competitions and track use?
Among several factors that make radial racing slicks effective is that they have minimal tread levels and only one contact patch. A tread pattern which divides the contact patch into separate parts or provides more tread density, on the other hand, would cause the tread block to squirm and degrade dry performance.
It implies that right before tyres burn out, they deliver the lowest wet grip and the highest dry performance. It’s also worth noting that the warmth produced when a tyre roll activates binding chemicals in its rubber.
While this cycle repeats over and over, the rubber components inside the tyre eventually stiffen and lose elasticity. This diminishes the tyre’s traction. For this reason, a shaved fresh tyre would give a better grip than a tyre worn to this tread density. It would take thousands of hours worth of driving.
Tyre shaving is efficient. Shaved tyres can achieve a tyre’s tack performance capabilities early in the tyre’s life. Furthermore, in several instances, shaved tyres used for racing have a lengthier lifespan than tyres employed at complete tread depth.
This procedure cuts the tread material and decreases the load of the tyre by quite a bit. A shaved tyre would typically lead to a minor expansion in the breadth of the tyre’s contact patch. This puts a bit more of the tyre on the track. Relatively shallow tread levels minimise the slip angle of your tyre, enhancing agility and turning ability by reducing tread block squirm.
Considering all the advantages, the next essential concern is which tyres to shave or to what degree you must shave them.
Max Performance, Extreme Performance and Ultra-High-Performance Summer Tyres
Because they’re not designed for race usage, many of these tyres start at a 10/32 inch tread profile. Trimming these to not over 6/32 inch of residual tread level provides a substantial increase. Shaving these to 4/32 inches allows the tyres to run much quicker at lap times.
To prevent the danger of burning or blistering the tread compound, tread heat must be closely supervised in any circumstances. Ensure levels do not surpass 210° F. There must be fairly uniform heat dispersal and wear on every tyre’s tread.
It’s worth noting that once raced on, all tyres would be slightly less efficient in the following racing season. Hence, we suggest shaving tyres to a level that survives not more than a single competitive season. If you must perform effectively in that race you participate in each year, using tyres trimmed to roughly 4/32 inches can help you even more.
A majority of Track or Competition tyres have a moulded tread profile of 6/32 to 8/32 inches. These do not need trimming before rallies, driving schools, track events, or competitive track performance in dry situations. Shaving Car Tyres Ashford could lead to a minor advantage in early lap times, but it would also lead to a loss in tread longevity.